HydroBlend™ Mid Volume Series 12 GPM Water Powered Proportioning Pumps
Hydroblend Proportioners are used extensively in the metalworking industry to mix water-soluble coolants, lubricants and low dilution high viscosity drawing and stamping compounds. Ensuring your metalworking concentrates are mixed properly, the Hydroblend will do its part to optimize your efficiency and profitability. At Hydroblend, quality and reliability are never compromised.
The Hydroblend is a water powered chemical metering pump and can therefore be located near an isolated water source without electrical connections. Installation is simple, straightforward, and takes very little time.
Metalworking concentrate will perform as intended only if it is diluted properly. A consistent and accurately diluted effluent will reduce waste, extend tool life, improve surface finish, and optimize sump life.
Applications:
- Cutting & Grinding Fluids
- Forging, Stamping and Drawing Compounds
- Soluble Oils
- Die Casting & Metal Stamping
- Parts Washers & Vibratory Finishing
Benefits:
- Reduces chemical waste
- Improves proportioning accuracy
- Easy installation
- Reliable operation
- Non electrical
- Adjustable
- Lowest Life Cycle Cost (Accuracy + Durability = Outstanding Value)
Water Driven Pumps use water to drive a piston which pumps concentrate into a mixing chamber where it is mixed with the water. The concentration is not affected by water pressure or the concentrate level, which makes them very accurate. These units can be hooked up in-line or to a hose reel and are typically used in central distribution systems.
Note: Plumbing codes in some areas may require a backflow preventer or other types of controls before the mixing system. Also, it is always recommended (and required for the warranty) to install a water pre-filter before the mixer.
- 12 gpm @ 75 psi
- Acrylic pump head and viton seals standard, other combinations are available
- Stainless steel valve block, outlet fitting, and main cylinder
- Reduces chemical waste, improves proportioning accuracy, repeatable formulations, easy installation, and reliable operation
- Water pre-filter included – 150 mesh/65 micron cleanable screen, garden hose fittings
- More models available – see specifications table – call for pricing
NOTE: Approximate 4-week lead time
HydroBlend™ Mid Volume Series 12 GPM Water Powered Proportioning Pumps
| MV6115-AV | 11.5 oz/gal | 1:100 | 1:11 | 0.90% | 8.30% | $1493.00 |
| MV6120-AV | 12 oz/gal | 1:100 | 1:10 | 0.95% | 9.10% | $1500.00 |
| MV6200-AV | 20 oz/gal | 1:60 | 1:6 | 1.60% | 13.50% | $1643.00 |
| MV6300-AV | 30 oz/gal | 1:40 | 1:4 | 2.40% | 20.00% | $1825.00 |
| MV6540-AV | 54 oz/gal | 1:25 | 1:2.5 | 3.20% | 32.00% | $2438.00 |
| MV6003-AV | 0.32 oz/gal | 1:4000 to 1:400 | 0.02% to 0.25% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 8 lbs. |
| MV6006-AV | 0.64 oz/gal | 1:2000 to 1:200 | 0.05% to 0.50% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 8 lbs. |
| MV6010-AV | 1 oz/gal | 1:1200 to 1:128 | 0.07% to 0.75% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 8 lbs. |
| MV6012-AV | 1.25 oz/gal | 1:800 to 1:80 | 0.10% to 1.20% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 8 lbs. |
| MV6025-AV | 2.5 oz/gal | 1:500 to 1:50 | 0.20% to 1.90% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 8 lbs. |
| MV6050-AV | 5 oz/gal | 1:260 to 1:26 | 0.35% to 3.70% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 9 lbs. |
| MV6064-AV | 6.4 oz/gal | 1:200 to 1:20 | 0.50% to 4.70% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 9 lbs. |
| MV6080-AV | 8 oz/gal | 1:160 to 1:16 | 0.60% to 5.80% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 10 lbs. |
| MV6100-AV | 10 oz/gal | 1:120 to 1:12 | 0.80% to 7.20% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 10 lbs. |
| MV6115-AV | 11 oz/gal | 1:110 to 1:11 | 0.90% to 8.30% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 10 lbs. |
| MV6120-AV | 12 oz/gal | 1:100 to 1:10 | 0.95% to 9.10% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 13 lbs. |
| MV6200-AV | 20 oz/gal | 1:60 to 1:6 | 1.60% to 13.50% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 14 lbs. |
| MV6300-AV | 30 oz/gal | 1:40 to 1:4 | 2.40% to 20.00% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 15 lbs. |
| MV6540-AV | 54 oz/gal | 1:25 to 1:2.5 | 3.20% to 32.00% | 12 GPM | 10-75 PSI | 3/4″ Garden Hose | 17 lbs. |
1. The first section of the model number denotes the Mid Volume (12 GPM) series pump and the maximum ounces injected per gallon of water.
2. The next section denotes the material used in the pump head (i.e. “A” stands for an Acrylic pump head).
3. The final section denotes the seal package used in the pump (i.e. “V” stands for Viton seals).
| Included Accessories | Mounting Feet, Suction Hose, Weighted Strainer/Footvalve, Operating Manual |
| Construction | Stainless Steel Valve Block, Outlet Fitting, Main Cylinder, and Chemical Cylinder |
| Alternative Pump Head Materials | A – Acrylic (standard)
PVC – Polyvinyl chloride HDPE – High Density Polyethylene (chemically resistant) K – Kynar/PDF (Paracetic Acid) |
| Alternative Seal Combinations | V – Viton (standard)
E – EPDM (specialty applications) TFE – Teflofluorethylene (chemically resistant) TTE – Teflofluorethylene (Lactic Acid) FS – Fountain Solution (Graphic Arts) PA – Perfluoroelastomer (Application Specific – Paracetic Acid) |
| Alternative Chemical Cylinder | Stainless Steel – Standard
316 Stainless Steel – Chemically Resistant Hastelloy – Chemically Resistant |
| Additional Options | DMAC – Hot Water Specific Delrin Machined Endplates
DI – Dual Injection TI – Triple Injection NPT – National Pipe Thread Adapters |
The mixture ratios and percentages presume chemicals with the approximate viscosity of water. A substantial increase in viscosity can reduce the proportioning specifications of the pump. HydroBlend will work with the chemical manufacturer, if appropriate, to determine the correct pump size.
Recommended Accessories & Replacement Parts
HydroBlend™ offers a variety of accessories to help with installation. Please contact HydroBlend directly by calling 208-375-5000 or emailing sales@hydroblend.com.
Industrial Plumbing Kits INCLUDE the water pre-filter along with everything necessary to install the Dosatron or HydroBlend Water-Powered Coolant Metering Pumps.
HydroBlend Custom Board Systems include key installation accessories all mounted on a poly board.
Related products
The HydroBlend™ Proportioner is ideal for diluting: Fountain Solutions (One & Two Step Formulations, Alcohol, Alcohol Substitutes, Web Conditioners, Silicone, and Aqueous Coatings) NOTE: Only models in stock are available in the cart. Call or email to purchase other models, which will require some lead time.
Dual injection pump with dual adjustment screws. If you are mixing two different oil bases with water, this costs less than two separate units! Very accurate.
HydroBlend™ double pump system with maximum chemical:water ratio 170:128, maximum flow 7 GPM @ 75 psi.